Bend-Tech software requires an active internet connection in order to activate the license on your computer, and then every 6 month. SE software can run offline in between. Don't have internet connection? See Dongle Key option.
Overview
- Bend-Tech PRO Software Be the first to review this product If you are designing chassis, roll cages, rock sliders, frames or anything from single parts to multiple tubing assembly then Bend-Tech PRO is where you want to start.
- Bend-Tech software requires an active internet connection in order to activate the license on your computer, and then every 6 month. SE software can run offline in between. Don't have internet connection? See Dongle Key option.
- Bending Software - Bend-Tech PRO: Bend-Tech PRO was introduced with our assembly interface which has taken the market by storm. With a modest price everybody can design and fabricate tubing like the pros. It is by far the most easy-to-use tubing design product on the market.
- Will Bend-Tech run on my computer? You can find system requirements under each software's product page. Does SE & Dragon CAD contain the assembly functions of PRO? 100% of the functions of PRO is included in the SE and Dragon CAD. Are the Bend-Tech products hard to use? No, we have worked very hard to make the Bend-Tech products easy to use.
Offline Programming Software
BendPro Office tube bending software is the same software that runs on a BendPro control at the bender. It is typically used in the office for Offline programming and performing simple part checks. Programmed parts can then be downloaded to benders on the shop floor via a network connection or via a USB flash drive, etc.
When used on a desktop PC, the software runs in a virtual CNC Mode with simulated I/O. This allows the user to check newly programmed parts by running them in Auto Cycle, Step Cycle, or Manual Mode. Everything that can be done at the bender can be done 'virtually' in the office.
BendPro Office software frees up your benders to run production and is also an excellent training tool for new operators.
When the Auto Cycle button is pressed the software performs extensive checks to make sure the part is programmed correctly and that there won’t be any problems with the Tooling Interference Zones as programmed, etc…
Being able to program new parts in the office and also 'run' them using the same screens and command buttons as the bender has makes for an excellent tool for training new operators.
There is also a Simulation option available. The Simulation option does everything that BendPro Office does with the addition of animating a 3D model of bending machines and checking for interference problems between the tube and the machine.
New Part Wizard
The New Part Wizard walks you through each screen step by step allowing for quick, easy, and error-free creation of new part programs.
Intuitive Part Editor
New customers are surprised by how quick and easy it is to program parts in BendPro, especially when compared to other control systems. The Parts Editor is designed to make data entry and editing intuitive and easy.
Tubes can be displayed in 3D on the screen for the purpose of verifying the part geometry and the bending orientation. Command buttons are included for rotating, spinning, panning and zooming in or out. Individual bends and straight lengths can be highlighted for review and verification.
The Tube can also be animated to show the bending orientation. And a screen capture button allows copy and paste functions into Windows programs including Outlook and Word, etc.
Bend Tools are automatically rendered by the software. Custom bend tools and tool sets can also be created using the Tool Editor and stored by part number.
Part Importing
Part files can be imported from CAD files in STEP and IGES formats, or from other bender controls including Eaton Leonard, Adaptive Motion, and Eagle. Office PCs, Excel spreadsheets, measuring machines, Supravision, ShipConstructor, etc., are also supported.
CAD Interface
With this option the BendPro pipe bending software can automatically import tube geometries from virtually any CAD program including SolidWorks, Solid Edge, AutoCAD, Inventor, CATIA, Pro-E, etc. STEP or IGES files can be imported directly into the BendPro software and automatically translated to true bend data. This makes programming new parts much easier and quicker while reducing data entry mistakes. A new version of our CAD interface now imports round, squares, rectangles and oval tubes.
Powerful Parts Manager
The Open Part menu can display and sort all part files based on part number, description, or material parameters. The BendPro pipe bending software can automatically backup all part files and machine parameters to a local or network drive or to the cloud. There is virtually no limit to the number of part files that can be stored and recalled. Part files can be automatically transferred to the bender by using a network connection or USB flash drive.
Virtual 'CNC Mode' with simulated I/O allows the user to check newly programmed parts by running them in Auto Cycle, Step Cycle, or Manual Mode.
BendPro Pipe Bending Software Features
- Program and check parts in the office to reduce machine downtime
- Can be used to optimize part programs to maximize production
- Reduce material scrap and improve efficiency
- Easy programming options include importing part geometries from CAD
- Convert STEP & IGES files to BendPro parts
- Convert XYZ Cartesian coordinates to YBC bend data
- Convert YBC bend data to XYZ Cartesian coordinates
- Import other bender manufacturers files
- Import or export Supravision files
- Display the tube in 3D for analysis and verification
- Determine Springback and Elongation values
- Calculate accurate cut lengths
- Print Part information and reports
- Train new operators in the office
FAQ
Do I need the BendPro Office Software?
This is optional software that is used to program parts in the office. The main advantage of programming parts in the office is to free up your bender for running production.
It can also be used for training new operators in the office.
Is this the exact same software that runs on the Bender PC?
Yes.
How to I transfer parts created in the office to the bender?
You can do this via a USB flash drive and/or via a network connection.
What are the PC system requirements?
- Microsoft Windows 10
- Microsoft Windows 8
- Microsoft Windows 7
- Microsoft Windows XP
- Minimum 2 GB of memory
Control Upgrade for CNC Benders
BendPro brings new life and performance to any CNC tube bender and has become the industry standard control system.
Customers tell us it offers the highest level of performance, reliability, and functionality available.
Companies standardize on BendPro because it works with all of their tube bending machines regardless of make and model.
Operators benefit from learning a single control system. Naturally, this reduces training time, down time, and scrapped material while increasing productivity.
Industry-Leading Features
CAD Interface
3D Simulation
Teach Modes
Increase Production & Quality
- Rapid and simultaneous motion of all devices
- Optimized machine sequences
- Extremely accurate and repeatable
Less Down Time
- Reliable Beckhoff Industrial PC
- Guaranteed long-term availability
- Best support in the industry
Your Benders Can Do More
- Interfaces to CAD, Measuring Machines, etc.
- Support for large-radius push bending
- Supports tube cutters, hole punches, and more
Bend Tech Pro Software Torrent
Powerful Upgrade for any Bender
Free Tube Bending Software
Upgrading your existing bender with BendPro is far less expensive than purchasing a new bender. And you can keep using your existing bending dies.
BendPro can be installed on site at your location; you won’t need to send your bender anywhere. Customers can have their existing benders upgraded with BendPro and also order it with most new benders on the market.
The list of benders supported by BendPro continues to grow and currently includes Addison, Eagle, Eaton Leonard, Pines, CSM, Chiyoda, COMCO, Keins, SOCO, YLM, MiiC, BLM, Pedrazzoli, and others.
Industry-Leading Features
CAD Interface
BendPro can import tubes geometries from virtually any CAD program including SolidWorks, Solid Edge, AutoCAD, Inventor, CATIA, Pro-E, etc.
STEP or IGES files can be imported directly into the BendPro software and saved as bender part or Supravision files. This makes programming new parts much easier and quicker while reducing data entry mistakes.
Tube Bending Software
New Part Wizard
The New Part Wizard walks you through each screen step by step allowing for quick, easy, and error-free creation of new part programs.
Intuitive Part Editor
New customers are surprised by how quick and easy it is to program parts in BendPro, especially when compared to other control systems. The Parts Editor is designed to make data entry and editing intuitive and easy.
3D Tube Display
Any programmed part can be displayed in 3D for the purpose of verifying the shape and bending orientation. Command buttons are included for rotating, spinning, panning, zooming, etc. The tube can also be animated to show the bending orientation.
3D Simulation
BendPro software has a powerful option called SIM that simulates the bending process to detect potential collisions between the tube, bending machine, and bend tooling.
SIM can also be used to determine optimal bending sequences in order to avoid collisions and also reduce cycle times.
Teach Modes
Programming interference moves is often a complicated and time-consuming process with other bender controls. BendPro has several options to make programming avoidance moves quick and easy.
Teach Mode is used for programming avoidance moves and for optimizing bending sequences to increase production.
Diagnostics
BendPro’s extensive built-in diagnostics can be used for real-time troubleshooting of all machine devices including sensors, valves, and servos.
Servo Scope
The Servo Scope can be used to quickly configure and tune servo devices. This powerful tool can also be used to occasionally give your bender an advanced tune-up. This helps increase the speed, accuracy, and repeatability of any servo device including motors, servo valves, and proportional valves.
Additional Standard Features
- Program parts while bending
- Multi-part sequencing
- Resume after E-stop without scrapping the part
- Resume after safety zone violation without scrapping the part
- Start bending at any bend number
- Open and closed collet bending support
- Hitch feeding
- Recapture the tube in the Pressure Die zone using Teach
- Programmable unload sequences using Teach
- Profiling of pressures and speeds
- Feedrate override (0-100% of programmed speeds)
- Electronic gearing of bend arm, carriage, PDA, etc.
- Springback and elongation compensation options
- 24 user-definable alarms
Available Options
- CAD interface for importing STEP, IGES, and ShipConstructor files
- CMM interface (Measuring machines including Romer, AICON, FARO, Eaton Leonard Vector, etc.)
- Desktop Programming Software
- Simulation Software (at bender and desktop)
- Push bending (large and/or multiple-radii)
- Robotic loader and unloader interfaces
- Programmable PSI package
- Tube cutter support
- Hole drilling and punching support
- Custom software
What's Included
What You Get
- The best tube bending software on the planet
- Rugged and Reliable hardware available worldwide. No proprietary components are used.
- Beckhoff Industrial PC has guaranteed long-term availability. You won't get this with consumer products such as tablet PCs or Android tablets.
- Engineering expertise. BendPro is backed by engineers that have many years of experience with control systems, software, and tube bending.
- New set of electrical schematics drawn specifically for your bender. Professional and easy to understand.
- Best tech support in the industry. With engineers in Colorado, Tennessee, and the UK, we cover multiple time zones.
- A support partner for life. With over 2500 tube bender controls in the field worldwide, we are here to stay.
Reliable Hardware
Industrial PC
We chose Beckhoff PCs and I/O modules because of their proven track record in industrial environments. Furthermore, the Beckhoff PCs and I/O modules are stocked worldwide and are guaranteed for long-term availability – something you will not get with consumer products such as tablet PCs or Android tablets.
Compact I/O System
A compact Beckhoff I/O rack mounts inside the bender’s main electrical cabinet and interfaces to sensors, valves, encoders, and servo drives. We use Beckhoff I/O terminals because of their rugged reliability, known performance, and long-term availability.
High Quality Components
BendPro’s hardware is of the highest quality, performance, and reliability. The control is housed in a compact, mobile, Rittal operator console with locking casters. The console is connected via high-speed EtherCAT (Ethernet) to a compact I/O system which consumes very little space in the bender’s electrical cabinet. Heavy-duty Allen-Bradley pushbutton switches and joysticks are used for machine operation at the console.
Tech Support
Customers tell us that our technical support is the best in the industry. We have support offices in Colorado, Tennessee, and the United Kingdom. We also offer online remote support using popular TeamViewer software, allow us to login to your BendPro control to help quickly diagnose problems, update software, activate new software features, re-tune servo drives, etc.
Images
HMT 3.5E-MS All-Electric CNC bender
With Digital Servos and 3D Simulation
CSM 18 TDRE CNC Hybrid benders
This Aircraft company is standardizing on BendPro
HMT ES5.0 Heavy Duty CNC bender
With Swing Away Wiper Die
Eaton Leonard VB 75 CNC bender
Interfaced to Eaton Leonard Vector CMM
SOCO SB-80x12A All Electric CNC bender
With Boost and Tube Cutter
Crippa CA 942 Electric CNC Bender
Interfaced to Romer CMM
Adaptive Motion CNC bender
With Electric Y axis Boost
Schwarze Wirtz CNC100DB bender
With Boost Clamp and Loader Interface
Horn 2 CNC bender
With Servo Pressure Die and Pressure Die Assist
Keins KB-10 Multi-Stack CNC bender
In the Current Tech Lab
Addison and CSM CNC benders
Tubecraft in the UK has standardized on BendPro
Pines 4 Semi-Automatic (NC) bender
With Programmable Boost direct on tube
Crippa CA 925 Electric CNC bender
With 3D simulation and Collision Detection
Addison DB 25 CNC bender
Interfaced to Romer Measuring Machine
FAQ
What are the advantages of upgrading my bender with BendPro versus buying a new one?
- It is far less expensive to upgrade your control system with BendPro then to purchase a new bender
- You can still use your existing bending dies; you don’t need to purchase new tooling
- BendPro performs better and is able to do more than the OEM controls being shipped on new benders
- We include new electrical schematics that are professional and easy to understand
- You will be supported for life by a US based company
Will I need to ship my bender somewhere to have a BendPro control installed?
No. BendPro can be installed on-site at your location. This will save you money on trucking costs and also reduce the amount of time your bender is down.
Will I be able to reuse my existing part files?
In some cases, yes. BendPro can import part files from some of the control systems made by Eaton Leonard, Pines, Adaptive Motion, and others.
Do I need to replace the servo drives and motors?
In most cases, no. BendPro can interface to almost any existing servo system. If your servos are obsolete and/or starting to fail, you might want to consider replacing them. We will quote replacement servos as an option. The servos can also be replaced later if desired.
Will BendPro work on any of my tube bending machines?
BendPro was designed to work on any rotary draw, CNC tube bending machines. Companies often standardize on BendPro for this reason; their operators only need to learn a single control system.
The following list includes some of the benders currently supported by BendPro:
- Addison
- Eagle
- Eaton Leonard
- Pines
- CSM
- Chiyoda
- COMCO
- Keins
- SOCO
- YLM
- Miic
- BLM
- Pedrazzoli
Will BendPro work on electric benders too?
Yes. BendPro can control all-electric benders, hydraulic benders, and hybrids.
Why should I choose BendPro?
Benefits include increased performance, reliability, functionality, ease of use, and excellent support by experienced engineers.
Do you charge for software upgrades?
Software updates are always available at no charge.
What about support?
You will have unlimited phone and internet support from experienced engineers at our offices in Denver, Nashville, and the UK.
Do we need to purchase the simulation software?
Not everyone needs simulation software. Companies that purchase this option are those that frequently bid on bending new part shapes. They want to make sure they have a bending machine that can produce the part without machine interference. The software also estimates cycle times, which also helps during the bidding process.
What options are available with BendPro?
Desktop programming and simulation software, as well as interfaces to CAD, CMMs, robots, loaders, unloaders, cells, tube cutters, hole punches, corporate networks, the internet, custom software, etc.
How long has Current Tech been in business?
Since 1988. With over 1800 tube bender controls in the field, we are here to stay.